Seite 1 von 1

Demontage Armaturenbrett

Verfasst: Mi Okt 26, 2016 18:51
von optikchrisi
Hallo,

möchte das Armaturenbrett demontieren um einerseits eine Verkabelung zu ändern. Ich habe einen "Schweizer" und da ist das Bremslicht orange (ist in Österreich ja nicht zugelassen), und andrerseits würde ich die Dichtung beim Tachometer tauschen. Jedoch ist die obere Schraube links neben dem Tacho ein furchtbares "Gefummel". Raus geht ja noch aber wieder rein. Gibt es einen Profitip? Habe sie bewusst noch nicht rausgeschraubt! :smoke:

Liebe Grüße

Christian

Re: Demontage Armaturenbrett

Verfasst: Mi Okt 26, 2016 19:24
von Hotzenplotz
Hallo Christian

Das Armaturenbrett ist mit Spezialverschlüssen befestigt. 90° gegen den Uhrzeigersinn drehen, und dann das Armaturenbrett mit einem flachen Schraubenzieher abheben.
Verfolge vorher die Verbaelung, und markier die Stecker, bevor Du sie trennst.

Re: Demontage Armaturenbrett

Verfasst: Mi Okt 26, 2016 19:46
von optikchrisi
Hallo Hotzenplotz,

dann habe ich ein anderes Modell, da bei mir die Befestigung mit "normalen" Schrauben samt Mutter und Beilagscheibe verschraubt ist. :(


Liebe Grüße

Christian

Re: Demontage Armaturenbrett

Verfasst: Mi Okt 26, 2016 20:27
von Stef@n
Das eine Modell heisst Hafi, das andere Pinzi... :mrgreen:
Gruß

Stefan

Re: Demontage Armaturenbrett

Verfasst: Mi Okt 26, 2016 20:33
von optikchrisi
[quote="Stef@n"]Das eine Modell heisst Hafi, das andere Pinzi... :mrgreen:
Gruß

Stefan[/quote

Hallo Stefan,

deshalb habe ich ja die Frage auf der "Hafiseite" gestellt! 8)

Liebe Grüße

Christian

Re: Demontage Armaturenbrett

Verfasst: Mi Okt 26, 2016 20:34
von Hotzenplotz
ups, falsche Abteilung

ziehe meine Aussage zurück und behaupte das Gegenteil :oops:

Re: Demontage Armaturenbrett

Verfasst: Mi Okt 26, 2016 20:41
von optikchrisi
Hallo Hotzenplotz,

kein Problem :wink:

LG

Christian 8)

Re: Demontage Armaturenbrett

Verfasst: Do Okt 27, 2016 7:38
von heinkeljb
If your dashboard is held in with nuts and bolts (screwdriver ends) then you will have to get learn to do things by "feel" - in other words, without looking at what is happening at the back of the dashboard.
The nut is likely to be a size 8mm, so an 8mm ring spanner in one hand, up behind the dashboard, feel where the nut is, put the ring spanner on and hold it tight. Undo the screw from the outside.

When you have taken the dashboard off, maybe you can make a "captive nut" arrangement to hold the nut in place so you do not have to bend your arm in three directions to get to it!

There are lots of thing on a Haflinger that were not thought out very well - They work, but just are not the best way of doing that task if you have to mend some thing! Classic example, the inspection covers on the side of the engine bay - not big enough to be able to take a cylinder head off and out of! (they don't line up properly either).

John

Re: Demontage Armaturenbrett

Verfasst: Do Okt 27, 2016 8:06
von optikchrisi
Hi John,

thanks for the tip. What kind of captive nut would you take?

Christian 8)

Re: Demontage Armaturenbrett

Verfasst: Do Okt 27, 2016 8:50
von optikchrisi
this kind of nut?

Christian

Re: Demontage Armaturenbrett

Verfasst: Do Okt 27, 2016 19:24
von heinkeljb
The bolt goes through a piece of tubing behind the dash. So there is just a plain hole going through the tube.

There are lots of different ways you could fix a captive nut, or even change the way the dashboard is fastened to the tubing.
In no particular order or even an exhaustive list the following methods spring to mind:-

Glue a nut to the back of the tube with 2 part epoxy glue.
Braze a nut on the back of the tube.
Weld a nut on the back of the tube.
Use something like this:-
http://www.zygology.com/store/pc/viewCo ... ?idpage=78
(You make the hole on the front surface of the tube just big enough for the POP jack nut to go through, then wind the bolt in and do it up tight, it pulls the threaded bit towards the front and it grips the inside of the tube to hold the threaded section in place)

I am sure you can think of something similar to do if bending you hand round up the back is too much trouble....

Regards,

John

Re: Demontage Armaturenbrett

Verfasst: Do Okt 27, 2016 22:31
von optikchrisi
Hello John,

you're the biggest. That was a very good tip :idea: .Thanks so much!!!

Greetings from Vorarlberg

Christian