Die Suche ergab 118 Treffer

von heinkeljb
Fr Jan 26, 2024 20:14
Forum: Haflinger Technisches
Thema: Optimierung Luftansaugverrohrung zum Luftfilter
Antworten: 7
Zugriffe: 1073

Re: Optimierung Luftansaugverrohrung zum Luftfilter

Reduce the amount of dust in the engine bay by making sure you have the rubber seal that goes around the bottom of the engine bay tin work to seal the gap between the tin work and the bodywork. Then clean the oil bath in the cyclone and also clean the paper air filter. If you have to do it every day...
von heinkeljb
Sa Jan 20, 2024 9:49
Forum: Haflinger Technisches
Thema: Handgas Hafi CH 1.Serie
Antworten: 9
Zugriffe: 2608

Re: Handgas Hafi CH 1.Serie

You can take the plastic handle off the hand throttle cable in the cab. Then make a collar with a hole in the middle that fits the hand throttle. In the side of the collar you make a hole with a thread in it that goes to the hole in the center of the collar. A bolt with a wing shape on the top (so y...
von heinkeljb
Do Nov 30, 2023 19:43
Forum: Haflinger Technisches
Thema: Ladekontrollleuchte geht nicht aus!
Antworten: 67
Zugriffe: 7551

Re: Ladekontrollleuchte geht nicht aus!

Well done for solving the problem! I have had my electronic regulator fitted for the last 5 years or so. If it has been well made, it should not give trouble. Far more likely that you have ignition problems with points / coil / capacitor / timing etc.

John
von heinkeljb
Mi Nov 22, 2023 8:38
Forum: Haflinger Technisches
Thema: Ladekontrollleuchte geht nicht aus!
Antworten: 67
Zugriffe: 7551

Re: Ladekontrollleuchte geht nicht aus!

Morning, The "flying fuse" is to protect the main wiring of the Haflinger, not the voltage regulator. The 20Amp fuse is good for that. If the Dynastart is built as original then there is no need to have any further protection for the voltage regulator as the voltage put out by the dynastar...
von heinkeljb
Do Nov 02, 2023 21:32
Forum: Haflinger Technisches
Thema: Ladekontrollleuchte geht nicht aus!
Antworten: 67
Zugriffe: 7551

Re: Ladekontrollleuchte geht nicht aus!

The expert advises 16Amp controller. It will not stress the Dynastart as much which will make it last longer. Do you actually use a trailer on every trip? Do you actually use the Auxillary heater for 6 hours at a time without the engine running? Do you actually use the heater continuously for 6 hour...
von heinkeljb
Mi Nov 01, 2023 8:29
Forum: Haflinger Technisches
Thema: Ladekontrollleuchte geht nicht aus!
Antworten: 67
Zugriffe: 7551

Re: Ladekontrollleuchte geht nicht aus!

Use the 16Amp one. The Haflinger Dynastart is not really rated to produce 20Amp continuously. Also, the amount of power it can produce reduces as it gets hot which, it will do being on top of hte engine and alos it's self generated heat. Change some of the bulbs for LED one will help as well unless ...
von heinkeljb
Mo Sep 11, 2023 7:31
Forum: Haflinger Technisches
Thema: Bremsflüssigkeit leer, kein Pedaldruck, kein Leck
Antworten: 10
Zugriffe: 1022

Re: Bremsflüssigkeit leer, kein Pedaldruck, kein Leck

If you have no brake pedal pressure then most likely the piston in the master cylinder is stuck at the bottom of the cylinder. You will have to take the master cylinder out and check. Fluid leak will be from somewhere you have not looked at yet. When you bleed the system, how are you doing it? Based...
von heinkeljb
Sa Sep 09, 2023 19:53
Forum: Haflinger Technisches
Thema: Bremsflüssigkeit leer, kein Pedaldruck, kein Leck
Antworten: 10
Zugriffe: 1022

Re: Bremsflüssigkeit leer, kein Pedaldruck, kein Leck

If the fluid is no longer in the reservoir, then it must have gone somewhere. Brake fluid goes from the reservoir to the master cylinder. It could be leaking from the bottom of the reservoir. Or it could be leaking from the pipe that goes to the master cylinder. The next place it could be leaking fr...
von heinkeljb
Di Sep 05, 2023 21:48
Forum: Haflinger Technisches
Thema: Ladekontrollleuchte geht nicht aus!
Antworten: 67
Zugriffe: 7551

Re: Ladekontrollleuchte geht nicht aus!

Yes, You can install it. Make sure you have the correct 25 Amp fuse in the circuit right near the regulator box (Controll box). Check the Charging bulb is good - if it does not work replace it. Start the engine and observe the charging light closely - If it goes out the moment the engine Revs go up ...
von heinkeljb
Mo Sep 04, 2023 18:32
Forum: Haflinger Technisches
Thema: Ladekontrollleuchte geht nicht aus!
Antworten: 67
Zugriffe: 7551

Re: Ladekontrollleuchte geht nicht aus!

Dynastart can be exchanged here:-

https://prokschi.at/haflinger/electrica ... -part.html

or rebuilt by this company:

www.dynamoregulatorconversions.com

Electronic Regulator can be obtained here:- www.dynamoregulatorconversions.com

John
von heinkeljb
So Sep 03, 2023 7:29
Forum: Haflinger Technisches
Thema: Ladekontrollleuchte geht nicht aus!
Antworten: 67
Zugriffe: 7551

Re: Ladekontrollleuchte geht nicht aus!

Look on this page to see a reconditioned Regulator or to send your one for repair.

https://www.autoquariat.at/shop/hafling ... chten/?p=3

John
von heinkeljb
Fr Sep 01, 2023 22:59
Forum: Haflinger Technisches
Thema: Ladekontrollleuchte geht nicht aus!
Antworten: 67
Zugriffe: 7551

Re: Ladekontrollleuchte geht nicht aus!

If when you take the regulator box apart you see any sort of heat damage, smell of burning - buy a new one! There is very little you can do to repair a regulator unless you are willing and capable of re-winding the coils with new insulated copper wire. It is also possible that you have burnt the wir...
von heinkeljb
Mi Aug 30, 2023 20:49
Forum: Haflinger Technisches
Thema: Gänge gehen nicht mehr rein
Antworten: 15
Zugriffe: 1524

Re: Gänge gehen nicht mehr rein

Start a new thread for this - Any answers we give will get lost in the thread which will make it difficult for some one who is looking for answers to a charging light problem.

John
von heinkeljb
Sa Aug 26, 2023 21:41
Forum: Haflinger Technisches
Thema: Gänge gehen nicht mehr rein
Antworten: 15
Zugriffe: 1524

Re: Gänge gehen nicht mehr rein

Glad you have found the issue. Make 100% sure the release bering is good or you will be taking the engine out again very soon. I did think you would find the issue insidethe clutch bell housing as there is very little to go wrong outside which you can not see, like a broken cluth cable or a broken /...
von heinkeljb
Mi Aug 23, 2023 22:03
Forum: Haflinger Technisches
Thema: Gänge gehen nicht mehr rein
Antworten: 15
Zugriffe: 1524

Re: Gänge gehen nicht mehr rein

Do you have any movement on the clutch pedal? Most likely something has broken in the clutch bell housing. Probably the release bearing arm or pins. Sounds like you are going to have to take the engine out. Not such a big job on a Haflinger. Easy with two people, and a hydralic jack on wheels. Remov...
von heinkeljb
So Jul 23, 2023 20:17
Forum: Haflinger Technisches
Thema: Rattern Kupplung
Antworten: 1
Zugriffe: 912

Re: Rattern Kupplung

It will either be the clutch release bearing (Throw out bearing) or one of the little springs has broken. Either way you will have ro remove hte engine so you can get to the clutch in the bell housing.

Do it NOW!!! The longer you leave it with driving the more damage it will do.

John
von heinkeljb
So Jul 23, 2023 8:24
Forum: Haflinger Technisches
Thema: Haflinger Serie 2 Tank aufarbeiten
Antworten: 3
Zugriffe: 830

Re: Haflinger Serie 2 Tank aufarbeiten

Hi Stefan, Unless you want to cut open the tack, you will have to use a chemical to clean the inside of the tank. You could try very small "pea shingle" stones and the cement mixer, but you runthe risk of the small stones going up the petrol feed pipe and getting stuck in there. Chemical c...
von heinkeljb
Mo Mai 08, 2023 8:46
Forum: Biete Haflinger
Thema: Verkaufe Haflinger 700AP
Antworten: 2
Zugriffe: 2899

Re: Verkaufe Haflinger 700AP

This shoud be saved!

John
von heinkeljb
Mi Jan 18, 2023 8:25
Forum: Haflinger Technisches
Thema: Problem in Linkskurven
Antworten: 12
Zugriffe: 3269

Re: Problem in Linkskurven

First thing I would do is take the Carb right off the vehicle and strip and clean it. Even better if you can clean it in an Ultrasonic cleaner. Put it back on and try driving again. Next would be to check the fuel tank pick up pipe - maybe there is someting in the bottom of the tank that rolls into ...
von heinkeljb
Do Jan 12, 2023 23:42
Forum: Haflinger Technisches
Thema: Exzenter Bremse
Antworten: 3
Zugriffe: 1731

Re: Exzenter Bremse

Part numbers for the eccentric bolt that adjusts the brake shoe clerance are as follows:- plate 6 01/0 Item 71 part number: 700.2.34.231.1 EXZENTERBOLZEN ECCENTRIC BOLT M12X1 DIN 936 Item 72 part number: 501.1.3444 FEDERSCHEIBE SPRING WASHER Item 73 part number:900.2316 SECHSKANTMUTTER HEXAGON NUT T...